loading

Poolking, your best swimming pool equipment manufacturer and supplier with more than 20 years experience.   ​​​​​​​  Email: sandy@poolking.co

Precautions for swimming pool equipment installation

With the construction of more and more swimming pools, do you know about the selection and after-sales service of swimming pool water treatment equipment? Swimming pool filter equipment - what matters should be paid attention to for new energy-saving gravity water treatment equipment? Precautions for installing swimming pool filter sand tank: Installation: The sand tank should be installed as close to the swimming pool as possible, preferably 0.5m below the pool surface. Make sure there is drainage in the place where the sand tank is installed. Important: Do not use cast iron pipe or hemp fiber pipe to connect the valve block, you must use plastic equipment and Teflon tape, the pipe head can be threaded or installed 1.5 to 2 inches of water supply pipe as a compensation. Amount of sand loading: In order to achieve the maximum efficiency of the sand tank, 0.5~0.7mm, such as grain-sized quartz sand should be used as the filter medium. These quartz sand must meet the specified standards, and then operate as follows; 1. When the sand tank is installed , the connecting pipe is also installed and sanded; 2. Remove the cover and joint; 3. Pour sand that meets the requirements; 4. Clear the sundries on the cover and joint; 5. Install the cover.

Precautions for installing gravity filter equipment: 1. Before installation of swimming pool equipment and supporting facilities, the concrete strength level, position, size, strength and flatness of the foundation should be checked, and they should meet the design requirements. 2. The machinery and ropes used for on-site transportation and hoisting of swimming pool equipment and supporting facilities should have sufficient strength, and the equipment should be properly protected during the handling process without damage. For the parts that have been equipped and adjusted in the factory, they must not be disassembled and transported at will.

3. Swimming pool equipment and supporting facilities should be in place, aligned and fixed according to the design drawings and installation instructions, and the installation accuracy should meet the requirements. 4. The construction and installation of electrical equipment should comply with the current national standards "General Specifications for Construction and Acceptance of Electromechanical Equipment Installation Engineering" GB 50231, "Low-voltage Electrical Appliances for Electrical Installation Engineering Are Public and Acceptance Specifications" GB 50254 and "Electrical Installation Engineering 1kV and The following wiring engineering construction and acceptance specification "GB 50258 regulations. Poolking is the best swimming pool equipment manufacturer and supplier in China. Poolking exists to provide the highest quality swimming pool equipment while offering competitive pricing..

GET IN TOUCH WITH Us
recommended articles
News Application Products Transport
Best Best Quality production environment Factory Supplier
Poolking Best Best Quality production environment Factory Supplier
Poolking Best Quality production environment Factory
Bigger is not always better when it comes to pool pumps. A pool pump that is too large can hinder filtration and can even damage a pool’s filter and/or heater. It is therefore very important to know the size of a pool before purchasing a pool pump. If there is additional equipment (such as water features) installed into the pool, it will have to be taken it into account when deciding what size pump is going to be purchased. The more equipment is installed into a pool, the more powerful the pump needs to be.
It is important to consult with a pool equipment expert, such as Poolking's Pumps, before buying a pool pump. The team at Poolking will be able to give our customers professional advice regarding the size of the pump they will need to purchase.
----It is best to replace the silica sand of sand filters every 1-2 years for the following reasons:
a During backwashing, the filtration bed volume will expand upwards by 1.2 to 1.3 times. The water flow will drive the filtration layer to flow up and down, causing the filtration material particles to collide with each other. Backwash will let the small sand evacuate.
b.Some silica sands will be welded when the acid and alkali are changed due to insufficient purity;
Therefore, the longer the time, the worse the filtering effect of the sand tank. Since backwashing will consume and take away some sand, we need to replace the sand in the sand tank within the specified period.
Commercial depth sand filter leading by Poolking
Hello, ladies and gentlemen. Today I'd like to introduce Poolking commercial depth sand filter.It is environmental protection and non toxicity.It can be used in large swimming pools, aquariums, aquaculture and other water applications.
no data

Best swimming pool equipment manufacturer - Poolkin will continue for innovative management and excellent quality. Imagination will subvert the future, intelligent manufacturing will lead the era, that's the motto of Poolking!

If you have any question,please contact us.

Contact: Sandy

Email: sandy@poolking.co

Sales Hot line: +86-20-34982303

WhatsApp:+86-13922334815

Add: No. 80, Danan North Road, Dagang Village, Dagang Town, Nansha District, Guangzhou City (temporary business premises)

Copyright © 2025 Guangdong Poolking filtration equipment manufacturing co. Ltd. - www.poolking.co All Rights Reserved. | Sitemap
Contact us
whatsapp
Contact customer service
Contact us
whatsapp
cancel
Customer service
detect