loading

Poolking, your best swimming pool equipment manufacturer and supplier with more than 20 years experience.   ​​​​​​​  Email: sandy@poolking.co

how to hook up pool filter hoses

Author: Poolking - Swimming Pool Equipment Manufacturer

How to Hook Up Pool Filter Hoses

Having a pool in your backyard can be a great way to relax and enjoy the warm weather. However, keeping your pool clean and clear can be a challenge. One of the most important components of your pool's filtration system is the pool filter.

If you're a new pool owner, figuring out how to hook up your pool filter hoses can be a bit confusing at first. In this guide, we will walk you through the process of hooking up your pool filter hoses so you can keep your pool clean and clear all summer long.

1. Gather Your Supplies

Before you begin hooking up your pool filter hoses, you will need to gather a few supplies. You will need your pool filter system, pool filter hoses, hose clamps, and a screwdriver.

Make sure that all of the components of your pool filter system are clean and in good condition. If you notice any cracks or damage on any of the pieces, you will need to replace them before you begin.

2. Identify the Inlet and Outlet Ports

Your pool filter system will have an inlet and an outlet port. The inlet port is where the water enters the filter, and the outlet port is where the filtered water is returned to the pool.

You will need to identify these ports on your pool filter system before you can begin hooking up your pool filter hoses.

3. Attach the Hoses to the Ports

Once you have identified the inlet and outlet ports on your pool filter system, you can begin attaching the hoses. Slide one end of the hose onto the inlet port, making sure that it fits snugly.

Next, slide the other end of the hose onto the outlet port, again making sure that it fits snugly. Repeat this process with the other hose.

4. Tighten the Hose Clamps

After you have attached the hoses to the inlet and outlet ports, you will need to secure them in place with hose clamps. Slide a hose clamp over each end of the hoses, and tighten them with a screwdriver.

Make sure that the hose clamps are tight enough to hold the hoses securely in place, but not so tight that they damage or crush the hoses.

5. Prime the Pump

Before you turn on your pool filter system, you will need to prime the pump. This means that you will need to fill the pump and the hoses with water to create a vacuum.

To do this, turn off the pool filter system and remove the pump lid. Fill the pump with water until it is almost full, and reattach the lid.

Next, loosen the air valve on the top of the filter tank. Slowly pour water into the inlet port until water comes out of the air valve. Once water is flowing out of the air valve, tighten it back up.

6. Turn On the Pool Filter System

After you have primed the pump, you can turn on the pool filter system. Check to make sure that water is flowing through the hoses and that there are no leaks.

It may take a few minutes for the water to start flowing through the system, so be patient. Once you see water flowing through the system, you can turn on the pool pump.

In Conclusion

Hooking up pool filter hoses may seem confusing at first, but it's actually a fairly simple process. By following these steps, you will be able to hook up your pool filter hoses with ease.

Remember to regularly check your pool filter system for leaks or damage, and clean or replace any components as needed. With a properly functioning pool filter system, you can enjoy a clean and clear pool all summer long.

.

GET IN TOUCH WITH Us
recommended articles
News Application Products Transport
After about 5~10days ,or when the reading of the pressure gauge on the pump side of the filter has increased by about 0.2bars since the last backwash , backwash the filter as follows:
1. Stop the pump
2.Close the valves on the suction and return lines.
3.Open the cover of the pump and empty the filter gasket .
4.Refit the cover
5.Open the valve to the drain outlet
6.Turn the lever to BACKWASH
7. Open the valves to the suction and return lines.
8.Start the pump .Rinse the filter for about 1 to 2 minutes until the water in the sight glass is clear .
NOTE : Any electric heater must be off .
9. Stop the pump
10. Turn the lever to RINSE , start the pump and rinse for about 15~30 seconds. Stop the pump and turn the lever to FILTER . This is the normal operating position .
11. Close the drain outlet valve and start the pump . Switch on the electric heater if any .
a. Power failure or motor protection tripped
b. Pump doesn't vent
c. Pump doesn't fill the water
d. Suction line/hose leaking
e. Transparent cover not properly installed - check filter basket - even bolts
f . Inlet suction process is too large g.) Total resistance loss exceeds the allowable range of the pump - recalculate the required pressure
h. Mechanical shaft seal leakage
Poolking’s Horizontal Sand Filters in Singapore Zoo
Singapore Zoo is covering an area of 28.3 hectares. Natural scene in the parkinstead of fences, creating a natural living environment for all kinds of animals. Thereare about 3000 animals running free and living peacefully with tourists. It has beeninstalled more than 40 nos POOLKING's stacking horizontal sand filters in Sea Lion,Manatee Penguin hall . POOLING is the first manufacturer in China to produce
stacked horizontal sand filter.
How To Prime Swimming Pool Pump?
Your swimming pool pump is the central circulation system of your pool. Without it, your swimming pool waters wouldn't be fit for swimming.
Poolking's super commercial sand filters in Moscow Zoo
Moscow Zoo(Московский зоопарк)is the first zoo in Russia with more than 1,000 kinds of animals .The zoo is the member of the World and European Association of Zoos and Aquariums.
no data

Best swimming pool equipment manufacturer - Poolkin will continue for innovative management and excellent quality. Imagination will subvert the future, intelligent manufacturing will lead the era, that's the motto of Poolking!

If you have any question,please contact us.

Contact: Sandy

Email: sandy@poolking.co

Sales Hot line: +86-20-34982303

WhatsApp:+86-13922334815

Add: No. 80, Danan North Road, Dagang Village, Dagang Town, Nansha District, Guangzhou City (temporary business premises)

Copyright © 2025 Guangdong Poolking filtration equipment manufacturing co. Ltd. - www.poolking.co All Rights Reserved. | Sitemap
Contact us
whatsapp
Contact customer service
Contact us
whatsapp
cancel
Customer service
detect