loading

Poolking, your best swimming pool equipment manufacturer and supplier with more than 20 years experience.   ​​​​​​​  Email: sandy@poolking.co

how to fix pool filter pump

Author: PoolKing - Pool Sand Filter Manufacturers

How to Fix a Pool Filter Pump

A swimming pool is one of the most enjoyable home amenities that provides a lot of fun during the hot summer days. However, maintaining a pool can be challenging, especially when it comes to fixing the pool filter pump. The pool filter pump is an essential component of a swimming pool, as it ensures that the water is clean, free from debris, and safe. However, when the pool filter pump is not working correctly, it can be frustrating and can put a damper on your swimming activities. In this article, we will show you how to fix a pool filter pump so that you can enjoy your swimming experience.

1. Troubleshoot the problem

Before you start fixing the pool filter pump, it is essential to troubleshoot the problem. Check for any visible signs of damage, such as cracks or leaks. Ensure that the pump is unplugged, and the breaker is turned off. Often, the issue is a clogged filter or a blocked impeller. If the filter is dirty, remove it and clean it. Use a garden hose to wash off any debris or buildup on the filter. If the impeller is blocked, use a straightened wire coat hanger to remove any debris. Also, check if the motor is making any unusual noise or overheating.

2. Replace the Pump Lid Seal

If your pool filter pump is leaking, it is likely due to a worn-out pump lid seal. The pump lid seal is located at the top of the pump motor, which is responsible for keeping the pump's lid in place. Over time, the pump lid seal can become worn-out or damaged, causing water to leak out. To fix this issue, turn off the pump, disconnect the power, and remove the lid. Using a flathead screwdriver, remove the old pump lid seal and replace it with a new one. Ensure that the new pump lid seal is correctly placed and secured in the groove.

3. Replace the Motor Bearings

If your pool filter pump is making a loud, grinding noise, it may be due to faulty motor bearings. The motor bearings are responsible for keeping the pump motor shaft in place and reducing friction. Over time, the motor bearings can become worn-out, resulting in noise or even a seizure of the motor. To fix this issue, turn off the pump, disconnect the power, and remove the motor from the pump housing. Using a wrench, remove the end caps from the motor and replace the worn-out bearings with new ones. Reassemble the motor and make sure that it is correctly aligned in the pump housing.

4. Replace the O-Ring

The O-ring is located between the pump housing and the seal plate, which prevents water from leaking out of the pump. Over time, the O-ring can become worn-out or damaged, causing water to leak out of the pool filter pump. To fix this issue, turn off the pump, disconnect the power, and remove the pump housing. Using a flathead screwdriver, gently remove the old O-ring and replace it with a new one. Ensure that the new O-ring is correctly placed and lubricated with O-ring grease.

5. Check the Electrical Connections

If your pool filter pump is not turning on or is turning off frequently, it may be due to a faulty electrical connection. Check the electrical connections to ensure that they are clean and tight. Make sure that the wires are not damaged or corroded. If necessary, replace any damaged wires and connectors. Also, check the circuit breaker to ensure that it is not tripped.

In conclusion, fixing a pool filter pump is not difficult if you follow the above steps. Ensure that you troubleshoot the problem before fixing it and take the necessary safety precautions. It is essential to keep your pool filter pump in good condition to ensure that your pool remains clean and safe to swim in. If you encounter any difficulties, contact a professional pool technician.

.

GET IN TOUCH WITH Us
recommended articles
News Application Products Transport
----Yes, they can. Silica sand is mainly used for filtration, while activated carbon is mainly used for adsorption. Silica sand is effective for higher water quality requirements. When use them together, silica sand should be placed on the bottom layer, and then activated carbon should be filled on the sand, but the cost of using two media is much higher.
After about 5~10days ,or when the reading of the pressure gauge on the pump side of the filter has increased by about 0.2bars since the last backwash , backwash the filter as follows:
1. Stop the pump
2.Close the valves on the suction and return lines.
3.Open the cover of the pump and empty the filter gasket .
4.Refit the cover
5.Open the valve to the drain outlet
6.Turn the lever to BACKWASH
7. Open the valves to the suction and return lines.
8.Start the pump .Rinse the filter for about 1 to 2 minutes until the water in the sight glass is clear .
NOTE : Any electric heater must be off .
9. Stop the pump
10. Turn the lever to RINSE , start the pump and rinse for about 15~30 seconds. Stop the pump and turn the lever to FILTER . This is the normal operating position .
11. Close the drain outlet valve and start the pump . Switch on the electric heater if any .
Poolking Filters in Liaocheng Underwater World
Liaocheng undersea world takes sightseeing, interactive experience and popular science education as its theme, including exploring Amazon, interactive exhibition area, jellyfish Pandora, boutique marine life, sea animal performance, theme exhibition area, popular science classroom, children's fun world, otter exhibition area, large water body (undersea tunnel), marine theater and other exhibition areas, and adds a variety of scientific and technological interactive experiences.
Opening Hours
----It is best to replace the silica sand of sand filters every 1-2 years for the following reasons:
a During backwashing, the filtration bed volume will expand upwards by 1.2 to 1.3 times. The water flow will drive the filtration layer to flow up and down, causing the filtration material particles to collide with each other. Backwash will let the small sand evacuate.
b.Some silica sands will be welded when the acid and alkali are changed due to insufficient purity;
Therefore, the longer the time, the worse the filtering effect of the sand tank. Since backwashing will consume and take away some sand, we need to replace the sand in the sand tank within the specified period.
How To Prime Swimming Pool Pump?
Your swimming pool pump is the central circulation system of your pool. Without it, your swimming pool waters wouldn't be fit for swimming.
Pool King 16th anniversary
1st Sep is Poolking's 16th anniversary celebration,today we have many games for our staffs to participate and they can award many gifts.
Let our business reach a new level and create a more brilliant future!
Using non metallic components fiberglass pressure tanks are rapidly replacing steel tanks in numerous applications. Fiberglass vessels offer several advantages in comparison with steel vessels .
Fiberglass vessels have a mechanical and chemical resistance superior to steel . Fiberglass tanks do not rust or corrode and are able to withstand damage from many types of water treatment chemicals.
Wholesale Best workmanship Supplier with good price - Poolking
Poolking Wholesale Best workmanship Supplier with good price - Poolking
Poolking Best workmanship Supplier
a. Power failure or motor protection tripped
b. Pump doesn't vent
c. Pump doesn't fill the water
d. Suction line/hose leaking
e. Transparent cover not properly installed - check filter basket - even bolts
f . Inlet suction process is too large g.) Total resistance loss exceeds the allowable range of the pump - recalculate the required pressure
h. Mechanical shaft seal leakage
no data

Best swimming pool equipment manufacturer - Poolkin will continue for innovative management and excellent quality. Imagination will subvert the future, intelligent manufacturing will lead the era, that's the motto of Poolking!

If you have any question,please contact us.

Contact: Sandy

Email: sandy@poolking.co

Sales Hot line: +86-20-34982303

WhatsApp:+86-13922334815

Add: No. 80, Danan North Road, Dagang Village, Dagang Town, Nansha District, Guangzhou City (temporary business premises)

Copyright © 2025 Guangdong Poolking filtration equipment manufacturing co. Ltd. - www.poolking.co All Rights Reserved. | Sitemap
Contact us
whatsapp
Contact customer service
Contact us
whatsapp
cancel
Customer service
detect