loading

Poolking, your best swimming pool equipment manufacturer and supplier with more than 20 years experience.   ​​​​​​​  Email: sandy@poolking.co

how to clean carvin pool filter

Author: PoolKing - Pool Sand Filter Manufacturers

How to Clean Your Carvin Pool Filter

If you own a swimming pool, you know how important it is to keep it clean and sparkling. A clean pool not only looks better, but it also keeps you and your family safe from harmful bacteria and other contaminants found in dirty water. One of the most important components of your pool's cleaning system is the filter. In this article, we will provide you with five easy steps to clean your Carvin pool filter and keep your pool water crystal clear.

Step 1: Turn off the Pump

Before you begin cleaning your Carvin pool filter, it is important to turn off the pump. This will prevent any water from flowing into the filter while you are working on it. Also, ensure that the pool's water level is below the skimmer to avoid any accidents due to water overflowing during the cleaning process.

Step 2: Remove the Filter from its Housing

To clean your Carvin pool filter, you need to remove it from its housing. There are different types of Carvin pool filters - sand filters, DE filters, and cartridge filters. To remove the filter, you need to follow the manufacturer's instructions on how to do it. Once you have removed the filter from its housing, place it on a flat surface.

Step 3: Clean the Carvin filter

The next step is to clean the filter. There are different ways to clean a Carvin pool filter, depending on the type of filter you have. For sand filters, you need to backwash the filter. To do this, you need to set the filter to backwash mode and let the water flow through it for several minutes. This will flush out all the dirt and debris that have accumulated in the filter.

For DE filters, you need to remove the DE powder from the filter grids. There are different methods to do this; you can use a hose to spray water on the grids, or you can soak them in a cleaning solution.

For cartridge filters, you need to remove the cartridges from the filter housing and then wash them thoroughly using a hose. Make sure that you remove all the dirt and debris that have accumulated in the cartridges.

Step 4: Inspect and Reassemble the Filter

After cleaning the Carvin pool filter, inspect it for any signs of damage. If you notice any damage, you may need to replace the filter. If there is no damage, you can reassemble the filter and place it back in its housing. Ensure that all the components are secure and tightly fitted to prevent any leaks.

Step 5: Restart the Pump

The final step is to restart the pump. Once you have cleaned the filter and reassembled it, you need to turn the pump back on. This will allow water to flow through the filter and remove any remaining dirt and debris. You can now relax and enjoy your clean and sparkling pool.

Conclusion

Keeping your Carvin pool filter clean is crucial for maintaining a safe and healthy swimming environment. By following the five steps we have outlined in this article, you can ensure that your Carvin pool filter is always functioning at its best. Remember to clean your Carvin pool filter regularly, as this will prolong its lifespan and keep your pool water crystal clear.

.

GET IN TOUCH WITH Us
recommended articles
News Application Products Transport
After about 5~10days ,or when the reading of the pressure gauge on the pump side of the filter has increased by about 0.2bars since the last backwash , backwash the filter as follows:
1. Stop the pump
2.Close the valves on the suction and return lines.
3.Open the cover of the pump and empty the filter gasket .
4.Refit the cover
5.Open the valve to the drain outlet
6.Turn the lever to BACKWASH
7. Open the valves to the suction and return lines.
8.Start the pump .Rinse the filter for about 1 to 2 minutes until the water in the sight glass is clear .
NOTE : Any electric heater must be off .
9. Stop the pump
10. Turn the lever to RINSE , start the pump and rinse for about 15~30 seconds. Stop the pump and turn the lever to FILTER . This is the normal operating position .
11. Close the drain outlet valve and start the pump . Switch on the electric heater if any .
Poolking won well-known brand awards for consecutive 3 years
On December 6, the 2021 China Swimming Pool Hot Spring SPA Industry Annual Conference was grandly held.     While commending outstanding brands, it also established a new benchmark in industry.                                                                       Poolking won  Well-known brand awards and Product excellent quality award.
----It is best to replace the silica sand of sand filters every 1-2 years for the following reasons:
a During backwashing, the filtration bed volume will expand upwards by 1.2 to 1.3 times. The water flow will drive the filtration layer to flow up and down, causing the filtration material particles to collide with each other. Backwash will let the small sand evacuate.
b.Some silica sands will be welded when the acid and alkali are changed due to insufficient purity;
Therefore, the longer the time, the worse the filtering effect of the sand tank. Since backwashing will consume and take away some sand, we need to replace the sand in the sand tank within the specified period.
Pool King 16th anniversary
1st Sep is Poolking's 16th anniversary celebration,today we have many games for our staffs to participate and they can award many gifts.
Let our business reach a new level and create a more brilliant future!
Poolking's top class sand filters in Chimelong Ocean Kingdom
Chimelong Ocean Kingdom is the largest ocean theme park in the worldwith rare marine animals, top-level amusement equipment and novel large-scaleshow, and strives to create the top-class, largest and most abundant amusementequipment leisure themed park.
Poolking's super commercial sand filters in Moscow Zoo
Moscow Zoo(Московский зоопарк)is the first zoo in Russia with more than 1,000 kinds of animals .The zoo is the member of the World and European Association of Zoos and Aquariums.
no data

Best swimming pool equipment manufacturer - Poolkin will continue for innovative management and excellent quality. Imagination will subvert the future, intelligent manufacturing will lead the era, that's the motto of Poolking!

If you have any question,please contact us.

Contact: Sandy

Email: sandy@poolking.co

Sales Hot line: +86-20-34982303

WhatsApp:+86-13922334815

Add: No. 80, Danan North Road, Dagang Village, Dagang Town, Nansha District, Guangzhou City (temporary business premises)

Copyright © 2025 Guangdong Poolking filtration equipment manufacturing co. Ltd. - www.poolking.co All Rights Reserved. | Sitemap
Contact us
whatsapp
Contact customer service
Contact us
whatsapp
cancel
Customer service
detect