loading

20년 이상의 경험을 보유한 최고의 수영장 장비 제조업체이자 공급업체인 Poolking    ​​​​​​​   이메일: sandy@poolking.co

how to set up intex easy set pool filter

How to Set Up Intex Easy Set Pool Filter

Summer is the time for enjoying hot weather and sunny days. What better way to relax than swimming in an Intex Easy Set Pool? But before you can jump in, you have to properly set up the pool filter. Follow these simple steps to ensure your pool is clean and ready for summer fun.

Step One: Unpack Your Pool Filter

When you first get your Intex Easy Set pool filter, take it out of the box and ensure that you have all the pieces. The filter pump should come with hoses, clamps, and a manual instruction guide. Read through the guide before starting the installation.

Step Two: Choose a Location for Your Pool

Before choosing a location for your pool, it’s important to take into account several factors such as the terrain, the amount of shade, and access to a power source. Once you’ve chosen a level location with good drainage, you can begin setting up your pool.

Step Three: Lay Out the Pool Liner

The next step is to lay out the Intex Easy Set pool liner. Unroll the pool liner and place it in the location you’ve chosen for your pool. Make sure the ground is smooth and free of any rocks, sticks, or debris that could puncture the liner.

Step Four: Inflate the Pool Ring

After you’ve laid out the pool liner, it’s time to inflate the pool ring. You can use a manual or electric pump for this step. Inflate the pool ring until it’s firm to the touch but still flexible.

Step Five: Fill the Pool with Water

Once the pool ring is inflated, it’s time to fill the pool with water. Use a garden hose to fill the pool and make sure you don’t overfill it beyond the recommended water level. As the pool fills up, the pool liner will stretch and conform to the shape of the pool ring.

Step Six: Install the Filter Housing Unit

After your pool is filled with water, it’s time to install the filter housing unit. The filter housing unit is an important component that helps keep your pool water clean by removing debris and unwanted particles.

Step Seven: Connect the Hoses

Once you’ve installed the filter housing unit, it’s time to connect the hoses. To do this, you’ll need to attach one end of the hose to the inlet of the filter and the other end to the outlet. Make sure you tighten the clamps securely to prevent leaks.

Step Eight: Prime the Pump

After connecting the hoses, it’s time to prime the pump. This step is important to ensure that the pump is properly operating before you turn it on. To prime the pump, turn off the power and open the air release valve on the filter housing unit. Fill the filter casing with water, then close the valve and turn on the pump.

Step Nine: Let the Pump Run

After priming the pump, it’s time to let it run for at least eight hours. This will allow the filter to circulate the water and remove any debris or particles that may have accumulated in the pool. After eight hours, you can turn off the pump and check the filter cartridge to see if it needs cleaning or replacement.

Conclusion

Setting up your Intex Easy Set pool filter is a simple process that can be done in just a few steps. By following these nine easy steps, you’ll have a clean and refreshing pool that’s ready for summer fun. Remember to always read the instruction manual carefully and take safety precautions when working with electrical components. Enjoy your new pool!

.

우리와 연락을 취하십시오
추천 기사
소식 애플리케이션 제품 운송
최고의 품질 생산 환경 공장 공급업체

풀킹 최고최고품질 생산환경 공장공급업체


풀킹 최고품질 생산환경 공장
약 5~10일 후 또는 필터의 펌프 측에 있는 압력 게이지의 판독 값이 마지막 역세척 이후 약 0.2bar 증가하면 다음과 같이 필터를 역세척합니다.1. 펌프를 멈춥니다.2. 흡입 및 복귀 라인의 밸브를 닫습니다.3. 펌프의 덮개를 열고 필터 개스킷을 비웁니다.4. 덮개를 다시 장착합니다.5. 배수구의 밸브를 엽니다.6. 레버를 BACKWASH로 돌립니다.7. 흡입 및 복귀 라인의 밸브를 엽니다.8. 펌프를 시작합니다.사이트 글라스의 물이 깨끗해질 때까지 약 1~2분 동안 필터를 헹굽니다.주의: 모든 전기 히터는 꺼야 합니다.9. 펌프를 멈춥니다.10. 레버를 RINSE로 돌리고 펌프를 시작한 다음 약 15~30초 동안 헹굽니다.펌프를 멈추고 레버를 FILTER로 돌립니다.이것이 정상적인 작동 위치입니다. 11. 배수 밸브를 닫고 펌프를 가동하세요. 전기 히터가 있다면 켜세요.
---Poolking은 전문 품질 관리팀을 통해 모든 제품이 포장 전 100% 검사를 거칩니다. 예를 들어, 필터 내부 탱크가 출고되면 보빈 와인딩 전에 1차 수질 검사를 실시합니다. 모든 연결부 또는 맨홀 및 사이트글라스 설치 후 2차 수질 검사를 실시합니다. 포장 과정에서 품질 관리팀은 와인딩, 넥, 내부 레진 등 모든 세부 사항을 검사하여 누수 및 결함이 없는지 확인합니다.
Poolking의 모래 필터 보증 기간은 유리 섬유 필터의 경우 3년, 플라스틱 필터의 경우 2년입니다. 보증 기간 동안 필터 부품에 손상이 있을 경우, 사진이나 영상을 통해 원인을 판단하여 무상 교체 부품을 제공해 드립니다. 필터가 심하게 손상된 경우 새 필터를 제공해 드립니다. 펌프와 조명은 필터와 동일하게 1년 보증합니다.
---- 모래 여과기의 실리카 모래는 다음과 같은 이유로 1~2년마다 교체하는 것이 가장 좋습니다.a. 역세척 시 여과층 용적이 1.2~1.3배 위쪽으로 팽창합니다. 물의 흐름에 따라 여과층이 위아래로 유동하여 여과재 입자가 서로 충돌합니다. 역세척을 통해 작은 모래를 배출할 수 있습니다.b. 산과 알칼리의 순도가 부족하여 교체할 때 일부 실리카 모래가 용착됩니다.따라서 시간이 길어질수록 모래 탱크의 여과 효과가 떨어집니다.역세척 시 일부 모래가 소모되어 제거되므로 지정된 기간 내에 모래 탱크의 모래를 교체해야 합니다.
데이터 없음

최고의 수영장 장비 제조업체 - 풀킨은 혁신적인 경영과 탁월한 품질을 위해 계속 노력할 것입니다. 상상력이 미래를 뒤집고, 지능형 제조가 시대를 선도할 것입니다. 이것이 풀킹의 모토입니다!

질문이 있으시면 저희에게 연락해 주세요.

연락처: 샌디

이메일: sandy@poolking.co

영업 핫라인: +86-20-34982303

왓츠앱:+86-13922334815

추가: 아니요. 광저우시 난사구 다강진 다강촌 다난북로 80호 (임시 영업소)

저작권 © 2025 광동 풀킹 여과 장비 제조 유한회사 유한회사 - www.poolking.co 모든 권리는 보호됩니다. | 사이트맵
문의하기
whatsapp
고객 서비스에 문의하십시오
문의하기
whatsapp
취소
Customer service
detect