loading

Poolking, nhà sản xuất và cung cấp thiết bị hồ bơi tốt nhất của bạn với hơn 20 năm kinh nghiệm    ​​​​​​​   E-mail: sandy@poolking.co

Precautions for use and daily maintenance of water pumps and sand cylinders

Precautions for the use and daily maintenance of water pumps and sand tanks 1. Specific operating sequence of various functions of water treatment filter sand tanks: Note: "*" is very important and must be performed 1. Check before starting the filter function: * - Before starting, the multi-way valve of the filter sand tank should be adjusted to the filter state* - Check whether the corresponding valves on the pipeline are in the correct state* - Check whether the hair collector is blocked. If blocked, it must be cleaned first; check whether there is air inside. If there is air, the air must be exhausted first* - Check whether the tank cover is tight and leak-proof. If there is leakage, the tank cover must be tightened to make it tight and leak-proof* - Check whether the liquid medicine pipe of each dosing system is normal and unblocked, whether there is liquid medicine in the medicine barrel, and whether the valve on the dosing device mouth is opened to ensure that the dosing system is in a ready-to-work state* - Check if there is air accumulated in the main return water pipe. If there is, it must be removed through the drain valve. 2. Start-up sequence - first turn on one water pump motor; after the water pump motor is running normally, turn on the water pumps in turn. The standby pump does not need to be turned on. Check after startup: record the pressure gauge index on the filter to check whether backwashing is required; check the operation of the water pump to see if it is running smoothly and without noise; check whether each dosing system is running normally; go to the swimming pool and visually check whether the water is flowing out of each water injection port normally. 3. Check the filter backwash function before starting - if the pressure gauge reading on the filter sand cylinder is higher than 2.5kg/cm2 or above, the filter sand cylinder must be backwashed immediately - confirm that the relevant water pumps of the sand cylinders that need to be backwashed have Stop operation - adjust the multi-way valve on the filter sand cylinder to the backwash state - confirm that the relevant valves on the pipeline are in the correct position 4. Backwash order - first run the water pump; check and observe the clear water mirror on the sand cylinder until the water is clean; then turn off the water pump Note: If the backwash water cannot be checked, the duration of each backwash should be 2-3 minutes 5. Rinse function Check before starting: Confirm that the backwash is completed; Confirm that the water pump is turned off; adjust the multi-way valve on the filter sand cylinder to the rinse state; Confirm that the relevant valves on the pipeline are in the correct position Rinse order: Start the water pump first; After the water pump runs for 1 to 2 minutes and then looks at the clear water mirror, turn off the water pump (the water is clear as the judgment standard) 6. Drainage function check before starting - adjust the multi-way valve on the sand tank to the drainage (Waste) state - confirm that the relevant valves on the pipeline are in the correct state - check whether the hair collector is blocked. If it is blocked, it must be cleaned first; check whether there is air inside. If there is air, the air must be discharged - check whether the tank cover is tight and leak-proof. If there is air leakage, the tank cover must be tightened to make it tight and leak-proof - check whether there is air accumulated in the main return pipe. If so, it must be discharged through the exhaust valve - if there is an overflow return pipe, please close the main valve on the overflow return pipe Note: During the drainage process, please try to prevent the water pump from interrupting its operation 7. Circulation function check before starting - before starting, the multi-way valve of the filter sand tank should be adjusted to the filter (Filter) state - adjust the multi-way valve on the sand tank to the circulation (Recirculate) state - confirm that the relevant valves on the pipeline are in the correct state - check whether the hair collector is blocked. If it is blocked, it must be cleaned first; check whether there is air inside. If there is air, - Check if the tank cover is tight and leak-proof. If there is a leak, tighten the tank cover to make it tight and leak-proof. - If there is an overflow return pipe, please close the main valve on the overflow return pipe. - Check if other equipment is in good condition. After starting up, check: whether the water pump is operating normally; whether other related equipment is operating normally. 2. Equipment maintenance: 1. Maintenance of water pump and hair collector* - When the three-phase water pump is turned on for the first time after installation, be sure to confirm that it does not reverse before turning it on* - If the water pump has abnormal noise or vibration during operation, it should be stopped and checked immediately* - If the flow rate of the water pump is far lower than the designed flow rate, it should be stopped and checked immediately* - The water pump must not run idly when there is no water* - The hair collector should be checked and cleaned frequently* - After cleaning, the air in the tank should be discharged before the lid is put back on, and a layer of oil should be applied to the rubber ring to seal it* - In winter, the water pump and hair collector should be drained before the water pump needs to be shut down for a long time. 2. Filter maintenance* -The multi-way valve on the filter must not be operated under pressure and must be operated in a shutdown and pressure-free state* -The multi-way valve must be switched to the right position during operation* -When the resistance of the sand tank increases to a certain extent (2.5kg/cm2), backwashing must be performed 3. Maintenance of the dosing system* -The dosing metering pump should be cleaned with clean water after the dosing is stopped every swimming season* -No granular drugs should be present when mixing the liquid medicine* -The dosing metering pump cannot run idle for a long time* -When no drugs are added, the valve at the outlet of the metering pump should be closed* -When the swimming pool is out of use for a long time, the medicine barrel, the filter head of the metering pump, the one-way valve and the hose should be cleaned 4. Control system* -The control system should be placed in a suitable location, kept dry and ventilated, and not damp* -It is best to be operated by trained personnel, and the operation must be strictly carried out according to the panel markings. III. Other matters needing attention: 1. All kinds of disinfectants should not be stored in the machine room, because they are seriously corrosive and make it difficult to breathe and cause metal surfaces to rust. Moisture-proof measures must be taken and they should be stored in a dedicated room. 2. Before or after the start of each swimming season, the entire water treatment system should be thoroughly cleaned, maintained and serviced. If the technical level is not enough, you can contact a professional water treatment company and entrust the equipment supplier to operate the comprehensive maintenance. 3. The machine room should be well ventilated, well-lit, well-drained, and kept dry for a long time. The automatic submersible pump in the machine room should be kept open (24 hours) 4. When operating the equipment, you should be careful and abide by all operating procedures. When operating the valve, you should move slowly to prevent water clocks from damaging valves, pipes or equipment. 5. The color of the pool water cannot be changed by simply adding algaecides (copper sulfate), but should be kept clear by continuous water treatment (if there is no algae, it should be avoided as much as possible) 6. When directly placing drugs in the swimming pool, make sure that there are no swimmers in the swimming pool. After completing the direct drug placement work, the swimming pool cannot be opened immediately. Before the swimming pool is opened for use, security measures must be taken to prevent the release of drugs and harm to the human body. 7. Always pay attention to the water level in the pool. The pool should be filled with water at all times. Floating objects, oily hair and other debris on the water surface should be discharged into the overflow ditch of the swimming pool.

Poolking is the best swimming pool equipment manufacturer and supplier in China. Poolking exists to provide the highest quality swimming pool equipment while offering competitive pricing. .

Liên lạc với chúng tôi
Bài viết được đề xuất
Tin tức Ứng dụng Vận chuyển sản phẩm
Máy lọc cát thương mại Poolking tại Atlantis Sanya

Văn hóa biển là nét đặc trưng chính của khách sạn. Phá Ambassador có 13500 tấn nước biển tự nhiên, có hơn 280 loại động vật nước ngọt và biển[4] Khách sạn có một bể cá "không gian bị mất". Du khách có thể ngắm nhìn hơn 280 loài sinh vật như cá mập, cá đuối, sứa, cá lộn ngược, lươn biển và cá lưỡi xương khổng lồ. Họ cũng có thể nhảy múa cùng các sinh vật biển kỳ lạ trong các dự án lặn. Ngoài ra, khách sạn còn tạo ra một thế giới nước có diện tích 200.000 mét vuông. Đây là công viên nước mở cửa quanh năm, có hàng chục đường trượt trên cao, chèo bè tốc độ, công viên nước vui chơi dành cho trẻ em, v.v. Khách sạn có 21 nhà hàng sang trọng trên thế giới, phục vụ các món ăn quốc tế như ẩm thực tự phục vụ của châu Âu, ẩm thực Trung Hoa tự phục vụ và ẩm thực Nhật Bản. Du khách có thể cảm nhận được văn hóa ẩm thực thế giới tại Hải Nam
Sử dụng các thành phần không phải kim loại, bình chịu áp suất sợi thủy tinh đang nhanh chóng thay thế bình thép trong nhiều ứng dụng. So với tàu bằng thép, tàu bằng sợi thủy tinh có nhiều ưu điểm hơn.
Bình sợi thủy tinh có khả năng chống chịu cơ học và hóa học tốt hơn thép. Bể sợi thủy tinh không bị gỉ hoặc ăn mòn và có thể chịu được thiệt hại từ nhiều loại hóa chất xử lý nước
----Poolking sử dụng nhiều máy móc sản xuất đẳng cấp thế giới để sản xuất sản phẩm và hệ thống kiểm soát chất lượng nghiêm ngặt cho từng sản phẩm. Nó xử lý một lỗi nhỏ với độ dung sai bằng không.
Không chỉ sản phẩm chất lượng tốt mà còn có dịch vụ sau bán hàng nhanh chóng và thỏa mãn cho khách hàng. Hãy để khách hàng tận hưởng làn nước trong vắt và dịch vụ thoải mái.
Nếu sản phẩm của Poolking có chất lượng tương đương nhưng giá cao hơn, làm sao Poolking có thể tồn tại? Tuy nhiên, Poolking có thể đánh bại các đối thủ khác và giành được nhiều thị phần hơn.
Poolking là sự lựa chọn tốt nhất của bạn!
----Có, họ có thể. Cát silic chủ yếu được sử dụng để lọc, trong khi than hoạt tính chủ yếu được sử dụng để hấp phụ. Cát silica có hiệu quả đối với các yêu cầu về chất lượng nước cao hơn. Khi sử dụng chúng cùng nhau, cát silica nên được đặt ở lớp dưới cùng, sau đó than hoạt tính nên được đổ lên trên cát, nhưng chi phí sử dụng hai vật liệu này cao hơn nhiều.
Poolking đã giành được giải thưởng thương hiệu nổi tiếng trong 3 năm liên tiếp

Vào ngày 6 tháng 12, Hội nghị thường niên ngành công nghiệp spa suối nước nóng hồ bơi Trung Quốc năm 2021 đã được tổ chức long trọng. Trong khi tôn vinh những thương hiệu xuất sắc, giải thưởng này cũng thiết lập nên chuẩn mực mới trong ngành. Poolking đã giành được giải thưởng Thương hiệu nổi tiếng và giải thưởng Sản phẩm chất lượng tuyệt vời.
không có dữ liệu

Nhà sản xuất thiết bị hồ bơi tốt nhất - Poolkin sẽ tiếp tục cải tiến quản lý và nâng cao chất lượng. Trí tưởng tượng sẽ thay đổi tương lai, sản xuất thông minh sẽ dẫn đầu thời đại, đó là phương châm của Poolking!

Nếu bạn có bất kỳ câu hỏi nào, vui lòng liên hệ với chúng tôi

Liên hệ: Sandy

E-mail: sandy@poolking.co

Đường dây nóng bán hàng: +86-20-34982303

WhatsApp: +86-13922334815

Thêm: Không. 80, Đường Bắc Danan, Làng Dagang, Thị trấn Dagang, Quận Nam Sa, Thành phố Quảng Châu (cơ sở kinh doanh tạm thời)

Bản quyền © 2025 Công ty sản xuất thiết bị lọc Guangdong Poolking. Công ty TNHH - www.poolking.co Mọi quyền được bảo lưu. | Sơ đồ trang web
Liên hệ chúng tôi
whatsapp
Liên hệ với dịch vụ khách hàng
Liên hệ chúng tôi
whatsapp
hủy bỏ
Customer service
detect