Poolking, your best swimming pool equipment manufacturer and supplier with more than 20 years experience.                                                                              +8613922334815


How to maintain swimming pool equipment


1. Operation plan 1. Prepare to open the first supply valve of the swimming pool equipment until the water is full to the overflow ditch, close the valve and open to balance the water tank valve 2. Turn on the circulating water pump to perform a purification cycle 3. Turn on the disinfection system 4. Dosing and chlorination 1. The acid metering pump is energized and put into use, and the data of the water quality monitor is adjusted to the normal value to make the whole system run normally and ensure that the water quality standard is within the normal value. 2. Operation content - operation of the filter system 1. Before opening, check whether all valves are opened and closed correctly? Is the hair filter filled with water? 2. Open the Y-type filter? Keep the seal intact 3. Check the noise during the operation of the pump 4. Clean the swimming pool before the initial operation. When the filter is running for the first time, run it in the recoil state for 10 minutes to remove the fine media and impurities in the filter. Stop the pump and put the valve in the washing position.

Start the pump and run for 1 minute, then stop the pump. 5. For normal operation, put the valve in the filter position to start the pump, pay attention to observe the flow and pressure of the filter, adjust the valve opening of the filter outlet pipe, and control the filter flow. The operating pressure must not exceed its maximum working pressure, that is, 0.25MPa. 6. Observe the filtration: When one of the following situations occurs - it needs to be recoiled. The filter pressure rises by 0.07MPa or 10PSIb compared with the initial pressure, and it runs continuously for 3 or 5 days.

When recoiling, first stop the circulation pump and close the heat medium water valve. Put the multi-channel valve in the recoil position, and then start the pump? Adjust the filter, and the valve opening of the recoil outlet pipe controls the recoil flow, and the recoil time is about 3 to 5 minutes. After the recoil is completed, stop the pump, set the valve to the washing position, start the circulating pump to wash for 1 minute, then stop the pump, set the valve to the filtering position, and then turn on the pump and the heat medium water valve.

Disinfection, PH balance system operation - Disinfection, PH balance system is to automatically measure the PH value and ORP value of the pool water by a fully automatic water quality monitor. Start the metering and dosing device as needed. Adjust the disinfectant content and pH value in the pool water.

1. Confirm that the valves of the water quality sampling pipeline are all open and the pipeline is unblocked 2. Turn on the power switch 3. According to the change of the pH value of the pool water? Select the "acid addition" and "alkali addition" control mode of the water quality monitor 4. Put the disinfectant , The PH balance agent dosing mode is in the "AUTO" automatic position 5. The flocculant is added manually according to the needs. Ph value 7.5~8.2 Residual chlorine 0.3~0.5 mg/L6. The foot-soaking pool ensures that the residual chlorine is 5~10 mg/L every day. Change it every 4 hours. Guangdong Boying Environmental Protection Equipment Co., Ltd. is a professional company specializing in R&D, production and sales of environmental protection water treatment equipment. The company's products are mainly used in swimming pool filtration systems, reclaimed water reuse systems, rainwater collection systems, ultrafiltration systems, building water supply and drainage and HVAC system, the main products are: stainless steel sand cylinder, hair collector, ultraviolet sterilizer, carbon steel and stainless steel multi-media filter, reverse osmosis pure water unit, vacuum degasser, automatic water supply and exhaust constant pressure device , Pressure expansion tanks, various water supply equipment, various water treatment equipment, etc.

Poolking is the best swimming pool equipment manufacturer and supplier in China. Poolking exists to provide the highest quality swimming pool equipment while offering competitive pricing..

Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
Current language:English