how to change sand in hayward s244t pool filter

2023/06/29

Author: Poolking - Swimming Pool Equipment Manufacturer

How to Change Sand in Hayward S244T Pool Filter


The Hayward S244T pool filter is a high-quality filtration system that helps keep pool water clean and clear. However, over time, the filter sand can become worn, and it is necessary to change it to ensure proper filtration. In this article, we will discuss how to change the sand in Hayward S244T pool filter.


Subtitles:


1. Why Change the Sand in Hayward S244T Pool Filter

2. Materials Required for Changing the Sand

3. Steps to Follow When Changing the Sand

4. Tips for Maintaining Your Pool Filter

5. Conclusion


Why Change the Sand in Hayward S244T Pool Filter


Changing the sand in your Hayward S244T pool filter is essential for maintaining optimal pool water quality. As the filter sand becomes worn, it loses its ability to filter out impurities and contaminants from your pool water. This can result in cloudy or dirty pool water, which is not only unappealing but also potentially unsafe for swimming.


Materials Required for Changing the Sand


Before you begin changing the sand in your Hayward S244T pool filter, you will need the following materials:


- Sand filter cleaner

- Pool filter sand

- Screwdriver or wrench

- Shop vac or hose

- Bucket or container

- Gasket sealant

- Lubricant


These materials can be easily found at your local pool supply store or online.


Steps to Follow When Changing the Sand


Step 1: Turn off the pump


Before you begin changing the sand, make sure to turn off the pump and remove any electrical cords from the outlet. This will prevent accidental electrocution while working on the filter.


Step 2: Backwash the filter


Next, you will need to backwash the filter to remove any loose debris and dirt that has accumulated in the sand. Attach a hose to the backwash valve and turn the valve to the backwash position. Turn on the pump and let it run for about two minutes until the backwash water runs clear.


Step 3: Remove the sand


After backwashing, you will need to remove the old sand from the filter using a screwdriver or wrench to detach the drain plug at the bottom of the filter. Allow the sand to drain out completely, either into a bucket or directly onto the ground.


Step 4: Clean the tank


With the sand removed, it’s time to clean the inside of the filter tank. Use a sand filter cleaner to remove any remaining debris from the filter walls and laterals. Rinse the tank thoroughly with a hose.


Step 5: Add new sand


Before adding new sand, it’s essential to check the laterals and replace any that are damaged or broken. Then, pour new pool filter sand into the filter until it reaches the appropriate level. Refer to the owner’s manual for specific instructions on how much sand to add.


Step 6: Reassemble the filter


After adding the sand, it’s time to reassemble the filter. Replace the drain plug, replace the top of the filter tank, and make sure all the clamps and bolts are properly tightened. Use a gasket sealant and lubricant on any seals and o-rings to ensure a tight seal.


Step 7: Run the filter and check for leaks


Finally, turn on the pump and check for leaks around the filter. Let the pump run for a few minutes to allow the sand to settle before returning the filter to its normal operating position.


Tips for Maintaining Your Pool Filter


Here are a few tips to help you maintain your Hayward S244T pool filter:


- Backwash your filter regularly to prevent a build-up of debris and dirt in the sand.

- Check the pressure gauge and backwash when the pressure is around 10 PSI higher than normal.

- Replace damaged or worn out laterals to ensure proper filtration.

- Add a filter cleaner to the sand every few months to help maintain its effectiveness.

- Replace the sand in your filter every three to five years or as needed.


Conclusion


Changing the sand in your Hayward S244T pool filter is a simple process that can help maintain optimal pool water quality. With the right materials and steps, you can easily replace the old sand with new pool filter sand, ensuring your pool stays clean and clear.

.

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry
Chat
Now

Send your inquiry

Choose a different language
English
Türkçe
ภาษาไทย
русский
Português
한국어
日本語
العربية
Deutsch
Español
français
italiano
Current language:English